Canoga-perkins 9160 10 Gigabit Ethernet Network Interface Device Instrukcja Użytkownika Strona 11
- Strona / 52
- Spis treści
- ROZWIĄZYWANIE PROBLEMÓW
- BOOKMARKI
Oceniono. / 5. Na podstawie oceny klientów
Set-up and Installation
This section describes how to set up and install the 9160. Before setting up the 9160, make sure the
serial cable (required to connect the chassis to a VT100 type terminal or PC) is available.
Install the 9160
The 9160 is tested and inspected before shipment from the factory. If there is obvious damage to the
shipping container, contact the carrier immediately.
Caution: Follow electrostatic discharge (ESD) safety precautions when handling Canoga
Perkins products, as with all electronic devices with static sensitive components.
1. Unpack the 9160. Keep the shipping container until the unit is installed and fully operational. In
the unlikely event that the unit is defective, contact Canoga Perkins Customer Service for a return
authorization number (RMA) and instructions on return shipment. For details, see Appendix A.
2. Mount the 9160 in a rack or as a standalone unit.
• Use the standard rackmount kit with brackets and screws to install the 9160 in a 19-inch rack or
use the optional 23-inch rackmount kit. The 9160 includes two sets of mounting holes.
• For a front chassis mount, align the screw holes in the brackets with the screw holes at the
front of the side panel of the 9160, then secure the screws.
• For a mid- or recessed chassis mount, align the screw holes in the brackets with the screw
holes in the middle of the side panel of the 9160, then secure the screws.
• To use the 9160 as a standalone unit, place it on a secure, flat surface within reach of the power
and fiber optic connections
3. Connect the power. The 9160 can be equipped for either AC or DC power.
• Plug the AC power cord into the socket at the rear of the 9160 and the wall socket.
Caution: Reversing the connections can damage both the DC source and the 9160.
• Connect power for the -48 VDC power supply at the terminal block; use 18 ga wire for the
+ and - connections and 20 ga wire for the gnd connection.
4. If not already installed, plug the XFP(s) into the 10G 1 port; the slot is keyed. To remove an
XFP, either lift the bail or press the button on the SFP, then gently pull it out.
5. If not already installed, slide an SP or the MP module into the rails and push it firmly into the
backplane, then tighten the captive screw(s).
Cabling for the 9160 includes the serial cable to the Terminal port, the Ethernet cable for a UTP port,
and the fiber optic link to the Tx and Rx ports.
6. Plug the serial cable into the serial port on the front panel and your PC. For the pinout, see
Chapter 5, Specifications.
9160 10 Gigabit Ethernet Network Interface Device 2-1
- 10 Gigabit Ethernet 1
- Network Interface Device 1
- User Manual 1
- CAUTION! 5
- ATTENCION! 5
- NOTICE! 5
- Table of Contents 7
- List of Figures 8
- List of Tables 8
- Overview 9
- Set-up and Installation 11
- Remote Fault 14
- Using the Software 15
- Management User Interface 16
- General Screen Format 16
- User Interface Organization 18
- Login and the Main Menu 19
- Managing the 9160 19
- Manage the Date and Time 21
- Manage SNMP and Host Access 21
- Manage Traps and Alarms 22
- View System Events and Traps 23
- Control Management Packets 23
- Update Software 24
- Managing Security 24
- Set Up User Accounts 26
- Change Your Password 27
- Manage Logged In Users 27
- Set Up Host Access 28
- Set Up LAGs 32
- Set Up VLANs 33
- Check the Static ARP Table 35
- Measure Receiver Input Power 38
- Troubleshooting 39
- New Installation 40
- Problems With Fiber Optics 40
- Running Diagnostics 40
- Test Latency and Jitter 40
- Test a Connection With PING 41
- Specifications 43
- 9160 Interface Model Numbers 44
- Warranty Information 47
Powiązane produkty i podręczniki dla Sprzęt komputerowy Canoga-perkins 9160 10 Gigabit Ethernet Network Interface Device
Sprzęt komputerowy Canoga-perkins N525 Ethernet Termination Service Unit Instrukcja Użytkownika
(104 strony)
(104 strony)
Sprzęt komputerowy Canoga-perkins N525 Ethernet Termination Service Unit Instrukcja Użytkownika
(109 strony)
(109 strony)
Sprzęt komputerowy Canoga-perkins 9145E Ethernet Network Interface Device Hardware Instrukcja Użytkownika
(54 strony)
(54 strony)
Sprzęt komputerowy Canoga-perkins 9145E NID Software Version 3.0 Instrukcja Użytkownika
(176 strony)
(176 strony)
Sprzęt komputerowy Canoga-perkins 9145E NID Software Version 3.1 Instrukcja Użytkownika
(189 strony)
(189 strony)
Sprzęt komputerowy Canoga-perkins 9145E NID Software Version 4.10 Instrukcja Użytkownika
(296 strony)
(296 strony)
Sprzęt komputerowy Canoga-perkins 9145E Network Interface Device Software Version 2. Instrukcja Użytkownika
(112 strony)
(112 strony)
Sprzęt komputerowy Canoga-perkins 9145E Standard NID Software Version 1.0 Instrukcja Użytkownika
(100 strony)
(100 strony)
Sprzęt komputerowy Canoga-perkins 9145E10G Network Interface Device Hardware Instrukcja Użytkownika
(55 strony)
(55 strony)
Sprzęt komputerowy Canoga-perkins 9145E10G NID Software Version 1.0 Instrukcja Użytkownika
(116 strony)
(116 strony)
Sprzęt komputerowy Canoga-perkins 9145EMP Network Interface Device Hardware Instrukcja Użytkownika
(50 strony)
(50 strony)
Sprzęt komputerowy Canoga-perkins 9145EMP NID Software Version 3.1 Instrukcja Użytkownika
(202 strony)
(202 strony)
Sprzęt komputerowy Canoga-perkins 9145EMP NID Software Version 4.0 Instrukcja Użytkownika
(229 strony)
(229 strony)
Panasonic TX14S4TP manuals
Owner’s manuals and user’s guides for Audio Panasonic TX14S4TP.
We providing 1 pdf manuals Panasonic TX14S4TP for download free by document types: User Manual
Komentarze do niniejszej Instrukcji